Go to documentation repository

Page tree

Documentation for Intellect 4.10.4. Documentation for other versions of Intellect is available too.

Previous page Vertical solutions  Database tables reference guide for Intellect and vertical solutions Next page


Skip to end of metadata
Go to start of metadata
Contents

 

Intellect base

XML fileParameterAvailable valuesDefaultProduct versionParameter in effect
<Archive storage drive>:\VIDEO\Settings.xmlRotateAngle0, 90, 180, 2700 

Sets the rotation angle of video image in the archive. If the rotation angle is specified in the video camera settings (see Configuring a rotation angle of video image), then this parameter is set automatically in Settings.xml file.

In Axxon player the archive is rotated at the specified angle when being played back or exported.
C:\ProgramData\elasticsearch-2.0.1\config\elasticsearch.ymlhttp.port0 - 655369200up to Intellect 4.10.2The parameter sets the port occupied by Elastic Search search engine. The value is to be the same as one specified in the cam_title.run.config file (see below).
C:\ProgramData\elasticsearch-5.2.2\config\elasticsearch.ymlIntellect 4.10.3 and later
<Intellect instalation>\Modules\cam_title.run.configElasticSearchPort0 - 655369200 The parameter sets the port Intellect sends data for Elastic Search search engine to. The value is to be the same as one specified in the elasticsearch.yml file (see above).
<Intellect instalation>\SlaveSettings.xmlDNS---This file stores the addresses of DNS servers specified using the Advanced Setup utility (see The Settings panel of the DNS section).

 

Intellect Web Report System

XML fileParameterAvailable valuesDefaultProduct versionParameter in effect
<Directory of the Intellect software installation>\Modules\Wt2\Web.configCamMonitorShift-5000 - 50000 

Sets shifting of video start while report viewing in milliseconds:

>0 – video will start later than time specified in a report

<0 – video will start earlier than time specified in a report

FaceReplaceCameraIpFromIP-address-up to 3.2Changes internal IP-address of a Server specified in the Architecture while viewing video for POS reports and for "Face" module report from outside
FaceReplaceCameraIpToIP-address-up to 3.2Changes external IP-address of a Server specified in the Architecture while viewing video for POS reports and for "Face" module report from outside
WorkThroughGatewaytrue, falsefalsefrom 3.3Enables receiving video from Gateway while viewing video for POS reports and for "Face" module report. A Gateway is selected authomatically.
PersonNameLength>=0-3.4

By default, the parameter is not added to the file (corresponds to value 1). 

Add it to the <appSettings> section in the following format: 

<add key = "PersonNameLength" value = "5" /> 

The parameter limits the user's patronymic to the number of characters specified in the value parameter for Access Manager and Time&Attendance reports. Example (if value = "5"): Ivanov Peter Alex.

If value = "0", the full name is displayed completely, without abbreviations. Example: Ivanov Peter Alexandrovich.

PersonNameIncludesId0, 1-3.4

By default, the parameter is not added to the file (corresponds to value 0).

Add it to the <appSettings> section in the following format:

<add key = "PersonNameIncludesId" value = "1" /> 

The parameter allows enabling display of the user ID in parentheses after the user full name in the Access Manager and Time&Attendance reports. 

value = "1" - the user ID in parentheses is displayed after the user full name. Example: Ivanov Peter Alexandrovich (1) 

value = "0" - the user ID is not displayed.

SweatheartingEnabled0, 103.4Enables the Sweethearting report.
SweatheartingAddItemPosFunctionNumber>=0-3.4Sets the Adding product to document function number from the dbo.FuncDic table, which is necessary for the Sweethearting report proper operation.
SweatheartingBeginReceiptPosFunctionNumber>=0-3.4Sets the function number used as the receipt beginning from the dbo.FuncDic table.
SweatheartingEndReceiptPosFunctionNumber>=0-3.4Sets the function number used as the receipt ending from the dbo.FuncDic table.
SweatheartingFilterByReceiptIntervals0, 103.4

Enables the sweethearting events filtering so that only the events which occured while the receipt was open were displayed in the Sweethearting report.

SweatheartingAddTimeoutMs >=05003.4

Sets the timeout between the sweethearting detector event and the POS event. If this timeout is exceeded, the sweethearting event is added to the Sweethearting report.

SweatheartingBeepEnabled 0, 103.4

Disables the sound notification about new events in the Sweethearting report.

SweatheartingStepCount >=010003.4

Sets the required number of the events which should be preloaded on the first Sweethearting report launch.

SweatheartingPreloadDays >=01403.4

Sets the required number of days the events from which should be displayed on the first Sweethearting report launch.

ExtendedPresenceReportInWorkplacetrue, falsefalse3.4

Enables an advanced display of the reports: Report on presence at the workplace and General report on presence at the workplace.

EnablePasskindReport true, falsefalse3.4

Enables a Report on issued passcards.

lpServerUrlIP-адресhttp://localhost:10001/lprserver3.4Sets the server address where the recognized LP images and the vehicle frames are stored.
IntellectVideoStreamNumber0-403.4

Sets the required camera stream number in live video reports (0 is the first camera stream).

ShowIconNewCashier true, falsetrue3.4

Highlights the new cashier's name in POS reports with the asterisk and the different color (the new cashiers are those who work less than a number of days specified in the CountDaysNewCashier key).

CountDaysNewCashier >=0303.4

Sets the number of days within which the cashier is considered a new one (the key is used together with the ShowIconNewCashier key).

QueueLengthDelta  0, 0.50.53.4

Sets the values threshold that are included into the table reports by Queue Length detectors:

0 - values equal to 0 and greater are included in the report.

0.5 - only the values greater than 0.5 are included in the report.

FACE-Intellect

XML fileParameterAvailable valuesDefaultParameter in effect
<Directory of the Intellect software installation>\Modules\face_client.run.configProblemImagesPath to a folderNone

Path to the folder for storing images which haven't been added to the database is specified in the parameter value. The specified folder will be created automatically.

Note.

If %USER% is specified in the parameter value, the images which haven't been added to the database will be stored in the folder:

c:\Users\%LOGGED_USER%\AppData\Local\AxxonSoft\FaceIntellect\ProblemImages\
AutoSizeColumnHeaderstrue, falsefalseActivates the automatic columns resizing of columns in the Face recognition and search interface window in proportion to its size when it is changed (see Setting the parameters for the Face recognition and search interface object).
AnalitycTimeout>=0100000Specifies the time in milliseconds for refreshing the analytical data in the Face recognition and search interface object. When the time expires, the Operation has timed out error will be displayed (see Viewing the analytical data).
RestRequestInterval>=0500Specifies the time interval in milliseconds between the HUAWEI module requests (see Configuring the HUAWEI face recognition module).

 

 

  • No labels